关于沼气发电机组日常保养维护方法的相关介绍
Introduction about the daily maintenance of biogas power generation unit maintenance method
沼气发电机组从运用之初起就要做好维护颐养事情，不只是为了沼气发电机组的正常运转，也是为了沼气发电机组不提早报废，为了最大的提拔收益，
Biogas power generation unit must complete the maintenance from the beginning of what use, not only for the normal operation of biogas power generation units, but also for biogas generating set not early retirement, in order to maximize the promotion benefits,
天天起动沼气发电机组前，查抄“四位”、“三漏” 查抄传动胶带 查抄发起机线束能否有干预或破坏，接插件能否有松动 查抄各衔接管路能否松动，各橡胶件能否有开裂或吸瘪征象 查抄空滤器指示器形态 留意：发起机的干净，只能用紧缩氛围吹净，忌用液体冲刷。查抄进气体系 查抄进气胶管能否有裂痕或穿孔，夹箍能否松动，若有发明应拧紧或改换，确保进气体系不漏气，不然会形成发起机破坏。空滤器颐养 发起机必需在装有空滤器的状况下运用，如空滤器指示器报警，应干净或改换空滤器滤芯。查抄传动胶带 查抄胶带能否有裂纹。
Every day before starting biogas power generation unit, check the "four", "three leakage" check drive belt to check the engine wire harness whether intervention or destruction, connectors can loose check the connection pipeline is loose, the rubber parts can crack or shrunken features check air filter indicator form note: the engine clean, only use compressed air blowing, avoid using liquid scour. Check the intake system to check whether there are cracks or perforated inlet hose clamp, loosening, if the invention should be tightened or change the intake system, ensure no leakage, or the formation of engine failure. The air filter maintenance engine air filter must be used in a condition, such as air filter indicator alarm, should be clean or replace the air filter element. Check the drive belt to check whether there are cracks in adhesive tape.
如呈现纵向和横向贯串的裂纹，胶带磨损或资料剥落等征象，应改换胶带。在胶带的最大跨距处丈量其挠度。最大挠度不该大于13mm。若有胶带张紧力丈量仪，可在胶带最大跨距处丈量其张力，张力极限为360～490N。改换冷却液滤清器 车辆中止运转后，务必等冷却液温度低于50℃后，方可拆下散热器加水盖。在改换冷却液滤清器前，先封闭收支水截流阀，以避免热的冷却液喷雾伤人！拆下冷却液滤清器并干净滤清座密封立体。先在滤清器密封橡胶垫圈外表涂一层薄机油，再装置冷却液滤清器，拧紧力矩24%26plusmn2N.m 装置完后，务必翻开冷却液滤清器收支水截流阀。
The crack as presented in the longitudinal and transverse throughout, tape or wear data peeling phenomenon, should change the tape. The deflection at the maximum span measuring tape at. The maximum deflection should not be more than 13mm. If a belt tension measuring instrument, the tape at the maximum span measure tension, tension limit is 360 ~ 490N. Change coolant filter vehicle suspension of operation, must wait for coolant temperature below 50 ℃, square can remove the radiator cap. In the change of coolant filter before the first payment, closed water shut-off valve, in order to avoid the heat of cooling liquid spray! Remove coolant filter and clean the filter seat sealing stereo. First coated with a thin layer of rubber washer oil seal in the filter device, and then the cooling liquid filter, tightening torque of the 24%26plusmn2N.m device after, must open the coolant filter and water shutoff valve.
再装上散热器加水盖。查抄及改换高压焚烧线 目视查抄高压焚烧线能否有腐化，断裂缝迹，磨损暴露或炙烤征象，若有上述征象务必改换高压焚烧线。先拆下线圈末了焚烧线，再卸下火花塞末了焚烧线，不可以硬行操纵。先将焚烧线套管沿火花塞孔向下推，直至听到“啪”的一声而且觉得到套管已装在火花塞上，再装置线圈端焚烧线。查抄及改换火花塞 在发起机停机形态下，先将焚烧线从线圈端撤除，再从火花塞端撤除。用火花塞套筒和加长杆、棘轮将火花塞逆时针拧松，留意火花塞不要完整离开基座螺纹。连续逆时针扭转火花塞长套筒，直到火花塞完整离开基座，将火花塞从装置座上当心掏出。
And then loaded on the radiator cap. Check and change the high incineration line visual inspection voltage incineration line whether there is corruption, fracture stitch, wear exposure or burn signs, if the above signs must change pressure burning line. Remove coil end burning line, and then remove the spark plug and incineration line, not hard line control. The first burning push wire sleeve downward along the spark plug hole, until you hear a "pop" sound and feel to the casing has been installed in the spark plug, and device for coil end burning line. Check and change the spark plug in the engine down form, the incineration line from the end coil removal, then from the spark plug terminal removal. Use spark plug socket and an extension rod, the ratchet will spark plugs counterclockwise unscrewing, pay attention to the spark plug not from the base thread. Continuous counter clockwise twist spark plug socket, until the spark plug from the base, the spark plug from the device seat watch out.
